The Cel-Fi QUATRA Fiber Range Extender is an optical fiber device that extends the maximum distance between the Network Unit and the Coverage Unit interconnect via fiber lengths up to 2000 meters. Plug and play installation.
MODEL NUMBERS:
K370-001 (QUATRA 1000/2000/1000 FN)
K360-001 (QUATRA 4000/4000i/4000e)
Caution: Cel-Fi QUATRA Fiber Range Extenders are sold in pairs. Purchase the Extender designed to work with your Cel-Fi QUATRA model. Other extender products will not work with Cel-Fi QUATRA.
| Model | Fiber QRE M/N | QRE M/N |
| QUATRA 4000/4000i/4000e | K360–001 | Q40–OE |
| QUATRA 1000/1000FN/2000 | K370–001 | Q34–E1000 |
|
Input from QAUTRA NU |
Output to QUATRA CU |
Fiber & Power Cable Configurations
Fiber Cable Configurations
Installation
STEP 1:
Locate and mount the QUATRA Fiber Range Extender unit
- Input and Output port LEDs should be clearly visible.
- Allow adequate ventilation.
- Do not mount in direct sunlight, near heat sources, or in weather
exposed areas. - Consult the user manual for the full list of requirements for fiber
optic cable. - The Cat 5e cables that connect the INPUT & OUTPUT port to the
Cel-Fi QUATRA Network and Coverage Units should not exceed 100 meters in length.
Caution: The category cables must be dedicated (proprietary data link)! The system will not function if common shared LAN resources are used with cabling (routers, switches etc).
STEP 2:
Connect INPUT and OUTPUT cabling
- Connect fiber and category cables first according to the instructions in the user manual. AC power should be connected after all the data cables are plugged in.
- RJ45 LED #1 (solid amber) indicates power.
- RJ45 LED #2 will blink green during initialization, and will be solid green when the QUATRA Fiber Range Extender has passed self-test and is operating normally.
- If both LEDs blink off periodically on a port, the port is resetting to try and establish communications with the Cel-Fi QUATRA Network Unit or Cel-Fi QUATRA Coverage Unit it is connected to. Check cables and connections if this occurs.
- If both INPUT LEDs are off, check the cable to the Cel-Fi QUATRA Network Unit and that the Cel-Fi QUATRA Network Unit is powered up.
- If both OUTPUT LEDs are off, check the cable to the Coverage Unit.
- For further assistance, please consult your installer or contact cel-fi.com/support.
Technical Specifications
| Item | Specification |
| DC Input Power | 54-57VDC |
| DC Output Power | 57 VDC |
| Data Rate (Ethernet) | 1000 Mbps Full Duplex |
| Data Rate (Optical) | 6.1 Gb/s minimum |
| Product Ingress protection | IP20 |
| Power Consumption | 133 watts max |
| Device Type | Class A |
| Ambient Operating Temp | 0 – 50°C |
| Relative humidity | 0 – 95% Non-condensing |
| Environment | Indoors |
| Mounting | Wall or shelf |
| Dimensions | 240.6 (L) x 110.5 (W) x 49.3 (H) mm |
| Weight | 2kg |
| Compliance | FCC Part 15, Class A & CE |
Safety Precautions
- Use this product indoors. It should not be used outdoors.
- AC power should be connected after all the data cables are plugged in.
- When installing the equipment, all the requirements of the manufacturer and the referenced standards must be met.
- There are no user serviceable parts inside.
Caution: Changes or modifications to this product not expressly approved by Nextivity may void your right to operate the equipment.
Caution: Cel-Fi QUATRA Fiber Range Extender heat sink edges may be sharp. Caution while handling.
Warranty
Nextivity Inc. provides a limited warranty for its products. For details, please refer to cel-fi.com/warranty.
Limitation of Liability
In no event shall Nextivity, nor its directors, employees, agents, suppliers or End Users, be liable under contract, tort, strict liability, negligence or any other legal or equitable theory with respect to the Products or any other subject matter of this Agreement (i) for any lost profits, cost of procurement of substitute goods or services, or special, indirect, incidental, punitive, or consequential damages of any kind whatsoever or (ii) for any direct damages in excess of (in the aggregate) the fees actually received by Nextivity from End User with respect to the Products actually purchased and paid for.
See cel-fi.com for list of patents covering this product.
Electromagnetic Compatibility (EMC)
This equipment has been designed and tested to fulfill applicable standards for:
- Radio frequency emission when installed according to the instructions and used in its intended environment.
- Immunity to electrical and electromagnetic phenomena when installed according to the instructions and used in its intended environment.
USA
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV/IT technician for help.